more torch test
Video Rating: 5 / 5
(may be broke/outdated!)
more torch test
Video Rating: 5 / 5
Unspillable.com is your gateway into to the intriguing world of energy mysteries, revolutionary fuels, and the science driving alternative energy solutions. Delve into the depths of covert agendas and unexplained phenomena surrounding energy sources while uncovering the latest advancements in renewable technologies. From debunking conspiracies to exploring the cutting edge of sustainable energy, we’re your go-to resource for unraveling the secrets shaping our energy landscape.
© 2024 All Rights Reserved
25 Responses
@iammrpope hho is not very powerfull at all, the machine i have has sustained several flash backs and you can barly here them wen there inclosed detonations , all those pop of valves and sht you see are bullshit they aint neccesary, if you dont build your cell robust enough to handle flash back it shouldnt be built, my bubbler is for washing naoh vapor from the spray mist, you can build flash back arrestors but i gave up on them, you dont need em if you obey simple rules
i’m kind of nervous about building this machine because of the flash back, seems to me if the gas is mixed before the torch tip the entire supply line and bubbler vessel are kind of a bomb waiting to be detonated, what is the principal where it does not trace back through the line and cause an explosion, i’m thinking because of the limited o2. Would it not be wise to build a unit that could seperate the gasses to be mixed later? or is that not feasible because of supply restrictions?
have you or anyone you know of been using an arc welder for the psu on one of these units, i was wondering if the voltage is too high, i would like to build one of the dry cells like you had in previous videos, maybe out of ss even though its a terrible conductor. why did you scrap that cell for this one?
@altoputz i no but im attempting to do this withought the need for oxygen i have to bie,,, if i can use this in a room that gives me more then a lousy 1400 watts to wrk with i would be alright
@iammrpope 400V 8 AMP RADIO SHACK, USING A COPPER END CAP HEAT SINK
it does very well, it gets kinda hot at 15 amps but i just dump water in the cup of the end cap and it cools it write off
what are the specs on the diodes your using on this unit
@NOBOX7 where are you at? I may be able to send you some.
@delvis11 koh is hard for me to get , i would have to order it but thanks for the info , naoh makes soap out of almost any organic substance
@delvis11 ok the ohms per m of ss is 720 , its 96 for iron and 180 for steel
@delvis11 dont get me rong i see what your saying but i just had to try this iron plate thing, its such a better conductor then the electro passive metals
@delvis11 not as bad as u would think , im running more test and the iron oxide we was seing was caused by the naoh converting the iron hydroxide into iron oxide , the iron hydroxide came from me running the cell with no elite, go to google books and look up electrolysis , they all use iron plates in the old days, and the iron oxide you get is black the ruct we seen was from anothner reaction, the black oxide is minimal, i intend to revers the polarity periodicly to blast off any build up
your going to have to use Stainless or nickel plates to get rid of the iron in the water. Leaching iron off the anode’s.
Have you tried KOH? for me it keeps the foaming down.
awesome man, i’m off to build one
@NOBOX7 You also could add a secondary Oxygen mixer so it gets a higher temp with less amp needed
You also could add a secondary Oxygen mixer so it gets a higher temp with less amp needed
What kind of electrodes are you using, you said “rusting up the watter” so i assume steel, the ‘green substance’ you mention is iron II hydroxide, (Fe(OH)2) its unstable in air, and only exists in solution as a suspension, this is the iron in your electrodeds being oxidized. You should use high surface area carbon plates etc. or platinum foil electrodes for max. eff. Also the closer they are together (while being >1mm distance) also more eff. Good job tho btw,
What kind of electrodes are you using, you said “rusting up the watter” so i assume steel, the ‘green substance’ you mention is iron II hydroxide, (Fe(OH)2) its unstable in air, and only exists in solution as a suspension, this is the iron in your electrodeds being oxidized. You should use high surface area carbon plates etc. or platinum foil electrodes for max. eff. Also the closer they are together (while being >1mm distance) also more eff.
@Lupinlethird i ment bronze wool
@69iron69 lol are u the mic gie, all i have is a phone dood , sry you cant hear it, yes i have a gas dryer but its not hooked up yet cus i dont need it for testing the cell and the dryer is perishable
@TheCombineify i build things with hho torches, u can produce very tiny very hot flames on the low setting that are very good to solder with , for percision soldering
do you have to dry the H2/O2 mix before you burn it? Also i cant hear you use a better mic
do you have to dry the H2/O2 mix before you burn it?
What are you supposed to do with this? or is it just experimental?
if any one has a oxy acetalene set up with this kind of torch i would love to see some footage of how fast it can melt 1/4″ all thread , just so i can see how much weaker the flame i have is.